藍森林首頁 | 返回主頁 | 本站地圖 | 站內搜索 | 聯繫信箱 |
 您目前的位置:首頁 > 自由軟件 > 技術交流 > 網絡通訊


    

藍森林 http://www.lslnet.com 2006年7月26日 13:28

配完PRI後TEI總是沒有數,二層起不起來,為什麼?


這是RUNNING中的
!
!
ip subnet-zero
no ip domain-lookup
ip name-server 202.99.124.115
!
isdn switch-type primary-net5
isdn voice-call-failure 0
!
!
controller E1 3/0
framing NO-CRC4
pri-group timeslots 1-31
!
controller E1 3/1
!
!
這是sh int s3/0:15的:
Serial3/0:15 is up, line protocol is up (spoofing)
Hardware is DSX1
Internet address is 10.254.0.1/16
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last input never, output 00:38:13, output hang never
Last clearing of "show interface" counters 00:38:19
Input queue: 0/75/0 (size/max/drops); Total output drops: 4
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
4 packets output, 12 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Timeslot(s) Used:16, Transmitter delay is 0 flags
這是sh controller e1 3/0的
E1 3/0 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (589 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 2:
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 4 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 0 Unavail Secs
Total Data (last 2 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 4 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 0 Unavail Secs
這是sh isdn statu 的:
Global ISDN Switchtype = primary-net5
ISDN Serial3/0:15 interface
******* Network side configuration *******
dsl 0, interface ISDN Switchtype = primary-net5
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 0 CCBs = 0
The Free Channel Mask: 0xFFFF7FFF
Total Allocated ISDN CCBs = 0
請高手指正,什麼原因會導致第二層不起?

大家都過節去啦?沒有人?高手請多幫忙呀!

自已頂一下,希望有人回復!

對了,不是TEI=0的問題,而是State = TEI_ASSIGNED的問題,如何成為多幀建立?即是MULTI-FRAME-ESTANBLISHED

各位高人,請給一個答案吧,我快鬱悶死了!

ISP沒有給分配TEI,看起來像是ISP的問題。
debug isdn q921有什麼輸出?

好像思科設備的TEI都是等於0的,所以也就沒有再管TEI=0這個問題。但在DEBUG ISDN Q921時,看不到對端發過來的信號。電信那邊說如果沒有配通就是忙音,我這邊發現我們有幾個局根本打不通PRI的號,報的是所撥號不存在。電信說別的都已沒問題,可能就我這邊的局有問題,不知所云!現在我很想知道到底問題出在那一邊!真是鬱悶!

自已頂一下!

頂是一種美德!
各位大蝦都來頂一下吧! :)

版主呢?回個帖吧!老長時間了!


Copyright © 1999-2000 LSLNET.COM. All rights reserved. 藍森林網站 版權所有。 E-mail : webmaster@lslnet.com