Ciscoworks2000 installation process
1, Ciscoworks2000 brief
Ciscoworks2000 include : LAN solution, routed WAN solution, Service management solution, VPN/Security management solution.
LAN solution include :
Ciscoworks2000 comnon foundation management, resource management essentials, campus manager, content flow monitor, nGenius real-time monitor and device fault manager.
Routed WAN solution include :
Ciscoworks2000 comnon foundation management, resource management essentials, nGenius real-time monitor, access control monitor, internetwork performance monitor
Service management solution include :
Ciscoworks2000 comnon management foundation, service-level manager, managenment engine (ME 1100)
VPN/Security management solution include :
Ciscoworks2000 comnon management foundation, VPN monitor, Creating secure policy manager Elite
2, the installation CD ONE
SUN SOLARIS 2.7 2.1 installation CD ONE THE 4th edition
① server requirements ⑥ ⑦ ⑧
Requirement Type Minimum Requirements
． System hardware Sparc Ultra 10.
． 17-inch color monitor.
． CD-ROM drive.
Memory (RAM) 256 MB (all CD One components).
Available ． 2 GB drive space on the partition on which you install the product (the
Default is /opt).
． Swap space equal to the amount of memory (RAM). For
Example, if your system has 256 MB of RAM, you need
256 MB of swap space.
System software Solaris 2.6 or Solaris 2.7
Additional software (Optional) Netscape Navigator 4.75
② sun solaris 2.7 patch :
． 106327-05
． 106980-10
． 107081-11
． 107636-03
． 108376-03 (Asian only)
③ installation
2-5
Step 1 As root, mount the CD One CD-ROM using either of the following methods :
． Mount the CD-ROM on the CD One server system.
． Mount the CD-ROM on a remote Solaris system, then access the
One server system from the CD-ROM.
Instructions.
Step 2 Run the installation program.
． For a local installation, enter :
# Cd /cdrom/cdrom0/
#. /setup.sh
． For a remote installation, enter :
# Cd remotedir
#. /setup.sh
A message may display :
Warning : User casuser already exists, the installation process will
Overwrite its privilege.
Do you want to continue (y/n)? [Y]
This message will not appear if this is the first time CD One, 4th Edition, has been
Installed on this machine.
Step 3 Press Enter if you receive the casuser message. The installation program adds the
New user casuser and the new group casusers to the system.
Note If CD One has previously been installed on this machine, the product
Will automatically be installed in the same location where CD One was
Previously installed.
A message displays :
Enter the location where the product will be installed or q to quit.
Default location (PKGROOT)? [/opt/CSCOpx]
One requires a directory named /opt/CSCOpx Note CD. If you select a
Different installation directory, the directory will be /opt/CSCOpx
Created and will be a link to the directory you selected.
Step 4 Press Enter to accept the default directory for product installation, or enter a
Different directory.
Step 5 Select one of the following :
1) NMS Integration Utility to install only the Integration Utility
(For information about the Integration Utility and third-NMS integration.
Refer to Using CiscoView. )
2) Common Management Foundation (CMF) Base Desktop to install a subset
Of the CMF
(Select this option only if the application you 'll be installing next requires the
CMF Base Desktop and you do not want CiscoView or NMS Integration Utility
Installed. )
3) CiscoView
4) CiscoView, NMS Integration Utility and CMF to install all CD One
Components (Recommended for most systems)

Step 6 Enter the number corresponding to the option you have chosen or q to quit. Installation of the first four new general election.
The Integration Utility will be installed now. The Integration Utility
Cisco integrates Cisco device packages and applications into
Third - SNMP management platforms. You can choose to integrate
With a third - SNMP management platform during this install or
Later.
Do you want to integrate with the third-product now (y/n)? [N]
Step 7 Select one of the following :
． n to integrate with a third-NMS after installation (this is the
Recommended choice to complete the installation more quickly, and to avoid
Data can third-installation errors)
If you select n, go to Step 8.
． y to integrate with a third-NMS during installation
If you select y, continue with steps a through c.
A. Select the adapter from the list of available adapters, or select other to choose
An adapter that is not listed (you will be prompted to enter the path name of
The adapter), or select none to integrate after the installation is complete.
If you select none, go to Step 8.
B. Enter the HTTP CPU location, or press Enter to accept the default
Location, /opt/netscape/netscape.
A message appears, asking if you want to enable download options from the
Cisco Web page (CCO).
C. Select one of the following :
． n to disallow future upgrades from the Cisco Web page.
． y to enable future upgrades from the Cisco Web page.
Enter your CCO user ID and password.

④ Client installed
Browser requirements :
Browser ． Netscape Navigator 4.75.
(Windows NT 4.0 Workstation and Server, Windows 98, Windows 2000
Professional and Server, Solaris 2.5.1, Solaris 2.6, Solaris 2.7, AIX 4.33.
HP-UX 11.0)
． Microsoft Internet Explorer 5.5 with Service Pack 1.
Java Virtual Machine (JVM) version 5.0.0.3167 or current shipping version.
To verify the JVM, select View "Java Console.
(Windows NT, Windows 95, Windows 98, Windows 2000)

1.3.1 Java runtime environment installed in the system.
Client configuration :
3-2
Step 1 : Enable Java and JavaScript
． Netscape Navigator-Select Edit>Preferences>Advanced. Select the
Enable Enable Java and JavaScript check boxes, then click OK.
． Microsoft Internet Explorer-Select Tools>Internet Options>Advanced.
Under the Microsoft VM heading, select Java console enabled, JIT
Compiler for virtual machine enabled, and Java logging enabled, then
Click OK.
Step 2 Set your CPU cache to at least 6 MB :
． Netscape Navigator-Select Edit>Preferences>Advanced>Cache. Set
Both the memory cache and the disk cache to at least 6,144 KB, then click OK.
． Internet Explorer-Select Tools>Internet Options>General, then click
Settings. Set the cache to at least 6 MB using the Amount of disk space to
Use slider bar. Click OK to close the Settings box and return to the DIALOG
DIALOG Internet Options box, then click OK again.
Step 3 : Configure your CPU to accept all Cookies
． Netscape Navigator-Select Edit>Preferences>Advanced. Select the
Accept all Cookies radio button, then click OK.
． Internet Explorer-Select Tools>Internet Options>Security. Select
Internet, and click Custom Level. Scroll to Cookies and select Enable for
Both, stored on your computer and per-session. Click OK, click OK again.
Step 4 Configure your CPU to compare each page with its cached version every time
It loads a page :
． Netscape Navigator-Select Edit>Preferences>
Advanced>Cache. Select the Every Time radio button, then click OK.
． Internet Explorer-Select Tools>Internet Options>General, then click
Settings. Every visit to the page Select the radio button, then click OK.
Note This option must be set to prevent Internet Explorer from using the
Cached information for help links. If it is not set, the first help link is
Displayed properly, but the second time you click a link, the first page
Is displayed again.
Step 5 : Change the default timeout to 20 minutes
． only-See the instructions on the Microsoft Internet Explorer Web Support
Site.
Step 6 Enable style sheets :
． Netscape Navigator-Select Edit>Preferences>Advanced. Select the
Enable Style Sheets check box, then click OK.
． Internet Explorer-Select Tools>Internet Options>General, then click
Accessibility. Make sure that the Format documents using my style sheet
Check box is not selected, then click OK to close the Accessibility DIALOG box.
Then click OK again to close the Internet Options box DIALOG.
Step 7 Change the default font to sans serif for improved readability :
． Netscape Navigator-Select Edit>Preferences>Appearance>Fonts.
Select a sans-serif font (for example, Arial) and a font size in the Variable
Width Font and Fixed Width Font selection areas, then click OK. The text
In the CPU window is redrawn using the new fonts.
． Internet Explorer-Select Tools>Internet Options>General, then click
Fonts. Select a sans-serif font (for example, Arial) from the Web page ruling
Plain text and font lists, and then click OK. DIALOG Click OK to close the box.
The text in the CPU window is redrawn using the new fonts.
If you have problems after configuring your CPU CPU, increase your disk
Cache settings.
After the web CPU is installed on the client machine, there are no additional
Disk space requirements. However, because the CPU uses the local machine 's
Disk to store cached information, make sure you have enough disk space for the
Amount of cached information you want to store. All information is One CD
CiscoWorks2000 stored on the server.
⑤ CISCOWORKS visit :
Http://server_name:1741
User name : admin password : admin

3. Installation campus manager
Step 1 As root, mount the Campus Manager CD-ROM, using either of the following
Methods :
． Mount the CD-ROM on the Campus Manager server system.
． Mount the CD-ROM on a remote Solaris system, then access the CD-ROM
From the Campus Manager server system.
Step 2 Run the installation program.
For a local installation, enter :
# Cd /cdrom/cdrom0/
#. /setup.sh
For a remote installation, enter :
# Cd remotedir
#. /setup.sh
Note Campus is installed in the same location as CiscoWorks2000
One CD. The default is /opt/CSCOpx.
The installation program checks for compatible patches, dependencies, and disk
Space.
Step 3 Answer any questions that result from the checks.
The installation program displays many messages about the various packages
Being installed and the services being started. The packages include application
Software and device adapter packages for all devices that can be managed with
Campus applications.
The installation completes, installing Campus in the same location as CD One
(/opt/CSCOpx By default). The CiscoWorks2000 Server is running.
If errors occurred during installation, check the installation log file
/var/tmp/ciscoinstall.log. For information about troubleshooting, refer to

4. Installation resource manager essentiall
1-9
Step 1 As root, mount the Essentials CD-ROM. You can either :
． Mount the CD-ROM on the CiscoWorks2000 Server system.
Or
． Mount the CD-ROM on a remote Solaris system, then access the CD-ROM
From the CiscoWorks2000 Server system.
Step 2 Start the installation program.
． For a local installation, enter :
# Cd /cdrom/cdrom0/
#. /setup.sh
#. /setup.sh
The installation program checks for required patches and other dependencies and
Displays :
1) Resource Manager Essentials
2) Resource Manager Essentials Incremental Device Support
3) All of the above
Select one of the items using its number or enter q to quit [q]
Note Option 3 is the most likely choice for new installations of
Essentials 3.3. If you try to install only one of the
Already on your machine without the other components, the
Installation fails.
Step 3 Enter 3 and press Return. The installation program checks dependencies and
System requirements.
． If there is not enough disk space to install Essentials and IDS, the installation
Program displays an error message and stops.
． If the minimum requirements are not met, the installation program displays
An error message and continues with the installation.
The installation completes without displaying more questions, and the system
Prompt appears.
4. Installation device fault manager (Note that the installation)
2-2
Step 1 Make sure your system meets these prerequisites :
． Required (or desired) operating system upgrades have been performed, and
Required service packs are installed.
． All installed applications are supported by CD One, 4th Edition. Applications
Not supported by CD One, 4th Edition, will be disabled when you upgrade
One CD.
． CD One, 4th Edition, has been installed.
Step 2 Close all open or active programs. Do not run other programs during the
Installation process.
Step 3 As root, log on to the system on which you will install DFM, and mount a local
Or remote CD-ROM drive. For instructions on mounting the CD-ROM, refer to
Step 4 Start the installation program by entering one of the following :
． For a local installation, enter :
# Cd /cdrom/cdrom0
#. /setup.sh
2-3
The installation program stops CiscoWorks2000, performs a requirements check.
And displays the following prompt :
WARNING : User casuser already exists, the installation process will
Overwrite its privilege.
Do you want to continue? (Y/n)? [Y]
Step 5 Press Return to confirm installing the packages with the correct privileges. The
Installation program displays the following installation choices (the choices may
Vary, depending on your configuration) :
1) CiscoWorks2000 Device Fault Manager
2) Device Fault Manager HPOV-NetView adapters
Step 6 Select one and press Return. This installs the complete DFM package, which
Contains DFM, the DFM incremental device support base package, the
HPOV-NetView Adapter, and the RME Adapter.
The installation program checks dependencies and system requirements.
． If there is not enough disk space for the installation, the installation program
Displays an error message and stops.
Note Do not be alarmed if you see the following message :
INFO : total size (MB) required = 87
This message applies to disk space required by the
Current set of individual packages being installed.
． If the minimum recommended requirements are not met, the installation
Program displays an error message and continues installing.
The installation proceeds without displaying any more questions, and the system
Prompt appears. The installation program copies the files to the CiscoWorks2000
/opt/CSCOpx Default installation directory ($NMSROOT).
Step 7 Unmount and eject the CD-ROM.
(Note operation)
Step 8 Specify the clients that are allowed to connect to the DFM server. (DFM provides this
Fine-grain control as an additional security feature. )
A. Unregister the daemons with the Blowfish manager :
- For DfmServer :
# $NMSROOT/bin/pdcmd U DfmServer
- For DfmBroker :
# $NMSROOT/bin/pdcmd U DfmBroker
(Can do) b. Decide which you want to specify hosts using the option with --accept
Arguments shown in Table 2-1.
For example, this command fragment would allow connections only from
Hosts lucy and ethel :
--accept=lucy, Ethel
C. Re-register the daemons with the Blowfish manager, specifying that the clients
Can connect to the broker and server (in this example, the DFM broker port is
9002):
- For DfmBroker (the following command is one line) :
$NMSROOT/objects/smarts/bin/brstart DfmBroker-e-r-f # $NMSROOT/bin/pdcmd "--output
--port=9002 --accept=lucy, Ethel that. . . --restore=$NMSROOT/objects/smarts/conf/broker.rps "
- For DfmServer (the following command is one line) :
# $NMSROOT/bin/pdcmd DfmServer-e-r-d DfmBroker-f $NMSROOT/objects/smarts/bin/sm_server
"--bootstrap=DFM_bootstrap.conf --accept=lucy, Ethel that. . . --output --name=DFM "
(Optional) d. Make sure that the client names and IP addresses are registered with 16.00
DNS if :
- You are running DHCP 和 ／ 或
- You specified the clients with hostnames
Step 9 To verify that the DfmServer process is running, log on to the CiscoWorks2000
Desktop as the administrator and select Server Configuration>
Administration>Process Management>Process Status.

5. Installation content flow manager (not much use)
Step 1 Log in as the root user as described in the "Becoming the Root User" section on
Page 2-1.
Step 2 Mount the CD-ROM. For detailed instructions, see Appendix B, "Mounting and
Unmounting the CD-ROM Drive. "
Step 3 Change to the mounted directory using the cd command :
# Cd /cdrom/cdrom0
Step 4 Start the installation script by entering the following command :
#. /setup.sh
The CFM verifies the system environment for software setup program
Installation.
6. Installation internetwork performance manager
1) installed in solaris
4-15
Step 1 Log in as the root user
Step 2 Mount the CD-ROM drive
Step 3 Change to the mounted directory using the cd command :
# Cd /cdrom/cdrom0
Step 4 Start the installation script by entering the following command :
#. /setup.sh
The following IPM setup program menu appears :
1) Review README File First (Recommended)
2) Install IPM Server and Client
3) Install IPM Client Only
4) Exit Setup
Please choose an option>
Step 5 Type the number of the desired installation option and press Enter. (Usually 2) The IPM setup
Program verifies the system environment for installation of the software.
The following message appears :
Enter the full pathname : Netscape CPU executable?
[/opt/netscape/netscape]
Step 6 To accept the default path for Netscape Communicator, press Enter. If the
Netscape Communicator executable file is located in a different directory than the
Default, type the full path (including file name) where the executable file is
Located.
The IPM installation program determines whether or not your system meets the
Hardware and software requirements for running IPM.
4-17
Step 7 If your system meets the requirements for IPM, the following prompt appears :
Do you want the Express Install (y/n)? [Y]
． To choose the Express Install which installs IPM using all default settings.
Press Enter.
． To choose the standard installation which prompts you for additional
Information such as port numbers, product path, and filename, type N and
Press Enter.
Step 8 If your system does not meet all the requirements for IPM, the installation
Program proceeds with the standard installation and you are prompted for
Information such as port numbers, product path, and filename.
Step 9 Verify that the installation was completed successfully by viewing the messages
Displayed at the end of the installation and by viewing the installation log. The
Installation log path is specified at the end of the installation script.
Step 10 Depending on the installation option you selected, a menu appears with options
To start the software or exit setup. If the installation was successful, select an
Option to start the software.
The following menu appears when you install the server and client software IPM :
1) Start IPM Server and Client
2) Start IPM Server Only
3) Exit Setup
Please choose an option>
The following menu appears when you install only the IPM client software :
1) Start IPM Client and Server Connect to Default Remote-cwb-sun4
2) Start IPM Client and Connect to Alternate Remote Server
3) Exit Setup
Please choose an option>
To start the IPM server and client at a later time from the command line, enter :
# Cd /opt/CSCOipm/bin
#. /ipm
To start just the IPM server at a later time from the command line, enter :
# Cd /opt/CSCOipm/bin
#. /ipm Start
2) the installation of Windows
5-5
Step 1 Log in as the administrator.
IPM Step 2 Insert the CD-ROM in the CD-ROM drive on the workstation. The IPM
Program files are automatically extracted from the CD-ROM. When all the files
Are extracted, the Internetwork Performance Monitor Setup window appears.
Note If the setup window does not appear automatically when you insert the
CD-ROM, go to the root directory and run the ipmfull.exe command.
Step 3 Click Next. The License Agreement window appears.
Step 4 If you accept the license agreement, click Yes. The Setup Type window appears.
Note The Setup Type window allows you to specify whether you are
Installing the IPM server, the IPM client, or both. If you are running
Windows 98, you can install only the IPM client, so the Setup Type
Window is unnecessary. Instead, the Select Program Folder window
Appears, and you should skip to Step 7.
Step 5 Specify whether you are installing the IPM server, the IPM client, or both :
． To install both, select IPM Client & Server, and then click Next.
． To install only the IPM client, select IPM Client, then click Next.
． To install only the IPM server, select IPM Server, and then click Next.
The Choose Destination Location window appears.
Step 6 Accept the default location, or browse to find a location, then click Next. The
Select Program Folder window appears.
Step 7 Accept the default folder, enter a folder name, or browse to find a folder, then
Click Next. The Select Server Configuration windowappears IPM.
IPM shows the Select Server Configuration window if you are
Installing only the IPM client. If you are installing the server IPM is the window
Similar, but the field is displayed instead of the DbPort Server Host field.
Step 8 If you are installing the IPM server, in the field enter a port number for DbPort
The IPM server database. The default port number is 44341/tcp.
If you are installing only the IPM client, in the field enter the name ServerHost
IPM server of the host on which the software is installed.
Step 9 (Optional) In the ServerPort field, enter a server port number. The default is
44342/udp.
If you are installing only the IPM client, verify that the server is using default IPM
44342/udp port number. If the IPM server is using a different port number, enter
That number in this field. The IPM client and server can communicate only if they
Are configured for the same port number.
Step 10 (Optional) In the WebPort field, enter a Web port number. The default is
1744/tcp.
Click Next Step 11. IPM asks you to confirm your choices, and the Start Copying Files
Window appears.
Click Next Step 12. The Setup Status window appears and the files are copied.
Step 13 When all of the files have been copied, and asks if you want to do regular IPM
IPM unattended backups of the database. If you want to enable this feature, click
Yes.
Step 14 The InstallShield Wizard Complete window appears. Installation is complete.
Step 15 IPM asks if you want to read the README file. The README file contains
Late-breaking information that might not be found in the product documentation.
Step 16 To read the latest information about IPM in the README file, select the
README check box and click Finish.

3) visit IPM
IPM client can connect server may also be used : http://serverip:1744 visit.
After the installation of the system found that the Chinese version of IPM in normal use, the system can be used only in English.

7. Install access control list manager
Step 1 Make sure your system meets all the requirements of a
Step 2 To become a superuser, enter su and the root password at the command prompt, or
Log in as root.
Step 3 Insert the CD into your CD-ROM drive.
The CD-ROM is automatically mounted into the /cdrom/cdrom0 directory. If you
Are running File Manager, a separate File Manager window displays the contents
Of the CD-ROM.
Step 4 : Enter
# Cd /cdrom/cdrom0
#. /setup.sh
Chapter 1 Installing ACL Manager
Installing ACL Manager on Solaris
Step 5 Enter y to agree to the terms of the copyright, then press Return.
If you are upgrading ACL Manager 1.2 to 1.3, the program prompts you to install
Back up data from the previous release. You should back up your ACL Manager
1.2 data.
If you are installing ACL Manager for the first time, go to Step 8.
Step 6 Enter y at the command prompt, then press Return.
Step 7 Enter the path for the backup directory, and then press Return.
After the data has been backed up, if the correct version of Essentials is not
Installed, an error message appears and the installation terminates.
Step 8 If Essentials is installed, this message appears on your screen :
Select component (s) you wish to install (all/none/q) ?[all] :
Type all, and then press Return.
If Essentials is running, the install program asks you whether you want to stop the
CiscoWorks2000 Daemon Manager or not. Type y to continue installing
ACL Manager. If you type n, the installation program exits.
The installation program displays the names of the files being installed server. If
ACL Manager you have upgraded from 1.2 to 1.3, the data is updated.
ACL Manager gets registered in the CiscoWorks2000 data backup framework.
After the installation is complete, the installation program restarts the
CiscoWorks2000 Daemon Manager.

8. Installation real monitor (hard)
1) to establish a secure Windows account :
;select Account managers start with button>settings>control panel>administerative tools>computer management; expand the local users and groups list;select users;form the action menu, select new user; creat the user-ngenius. Select start button>settings>control panel>administerative tools, "local secureity policy; expand the local user rights policies list;select assignment;grant the user rights to the new user : log on as a solvents job.log on as a service.log on locally.
2) the installation of real-time monitor

① log in as administerator
Second, insert the CD
③ displays.click next to continue the welcome window.
④ click next.
⑤ click next.
⑥ click next.
⑦ accept or change the following information : web server port database server port
NGenius user account name nGenius user account password Login
⑧ enter the database password.
⑨ owner information in the installation the following information panel.enter
Log in name
Password
Russia, Kazakhstan, click next.
(11) click next.
(12) click yes.
(13) click ok.
(14), click yes.
(15) end.
RTM operation
At the beginning of menu 按start nGenius server.