Fa0/1 trunk done for a 3 Switch 2950 switches (2 months of 2950 is the core switches to 4506), the other port has been used for vlan11 normal, which is an arbitrary one based on the need to port as the vlan10. At this time the 10-port serial terminal for the Orange network also broken links or ip address. However, the port will need to plan on links to other vlan, beacons were normal. Vlan10 also used in other switches normal. I do not know where the start to solve this problem. Try to build a plane in the vlan10 Switchport turnk allow vlan 10 The above methods tried not! At 2 and 3 switches use show vlan results are as follows : 3 (in Taiwan Switch divided into 5, 9, 11 have links)
Sw-2950_ffcbgl#sho vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
5 VLAN0005 active
9 VLAN0009 active
11 VLAN0011 active Fa0/2, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type Mr. SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500-- - --0 0
5 enet 100005 1500-- - --0 0
9 enet 100009 1500-- - --0 0
11 enet 100011 1500-- - --0 0
1002 fddi 101002 1500-- - --0 0
1003 tr 101003 1500-- - --0 0
VLAN Type Mr. SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1004 fdnet 101004 1500-- - ieee-0 0
1005 trnet 101005 1500-- - ibm-0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Sw-2950_ffcbgl#
2 (3, the next level)
Sw-2950G_ffchyl>en
Password :
Sw-2950G_ffchyl#sho vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/2
2 PC_Server active
3 Dial&Router active
4 DongShi active
5 ChangBan active
6 BeiJian active
7 GongXiao active
8 CaiWu active
9 ShuJuCaiJi active Fa0/3, Fa0/4, Fa0/5, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/24
10 CheJianBanGong1 active Fa0/23
11 CheJianBanGong2 active Fa0/1, Fa0/6, Fa0/7, Fa0/15
IMC active 12
Training active 13
14 topix active
15 todmz active
16 BeiMeiChang active
50 FangYuanGongSi active
100 ForTRaining active
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type Mr. SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500-- - --0 0
2 enet 100002 1500-- - --0 0
3 enet 100003 1500-- - --0 0
4 enet 100004 1500-- - --0 0
5 enet 100005 1500-- - --0 0
6 enet 100006 1500-- - --0 0
7 enet 100007 1500-- - --0 0
8 enet 100008 1500-- - --0 0
9 enet 100009 1500-- - --0 0
10 enet 100010 1500-- - --0 0
11 enet 100011 1500-- - --0 0
12 enet 100012 1500-- - --0 0
13 enet 100013 1500-- - --0 0
14 enet 100014 1500-- - --0 0
15 enet 100015 1500-- - --0 0
16 enet 100016 1500-- - --0 0
50 enet 100050 1500-- - --0 0
100 enet 100100 1500-- - --0 0
1002 fddi 101002 1500-- - --0 0
1003 tr 101003 1500-- - - srb 0 0
1004 fdnet 101004 1500-- - ieee-0 0
VLAN Type Mr. SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1005 trnet 101005 1500-- - ibm-0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Sw-2950G_ffchyl#
Switchport vlan turnk allow VLAN 10 through 10 can let the other pass VLAN Switchport turnk allow vlan 10 You are not above the levels of 2950 VLAN10
Is it necessary? ? ? Solve the problem but I do not know why! Find a solution to be configured to their needs in a 2950 run sw-2950_ffcbgl#sho
Building configuration. . .
Current configuration : 2489 bytes
!
Version 12.1
No service PADE
Killing uptime service timestamps
Service timestamps log uptime
No service password-encryption
!
Hostname sw-2950_ffcbgl
!
Enable password cisco
!
Ip subnet-zero
!
!
Spanning-tree mode pvst
No spanning-tree optimize bpdu transmission
Spanning-tree extend system-id
!
!
!
!
Interface FastEthernet0/1
FuFeiHuaYanLou description Up Line
Switchport mode trunk
!
Interface FastEthernet0/2
Switchport access vlan 11
Switchport mode access
!
Interface FastEthernet0/3
Switchport access vlan 11
Switchport mode access
!
Interface FastEthernet0/4
Switchport access vlan 11
Switchport mode access
.
.
.
Interface FastEthernet0/12
Description YiBiaoW4
Switchport access vlan 10
Switchport mode access
!
Interface FastEthernet0/13
Description YiBiaoW3
Switchport access vlan 10
Switchport mode access
.
.
.
Interface FastEthernet0/24
Switchport access vlan 11
Switchport mode access
!
Interface Vlan1
255.255.255.0 ip address 172.16.1.24
No ip route-cache
!
Ip default-gateway 172.16.1.1
No ip http server
!
Line con 0
Creating password
Login
Line vty 0 4
Creating password
Login
Line vty 5 15
Login
!
!
End
Cross it will be received with the higher level of exchange is also its trunk, to show exactly vlan watched a v10 and v11, then it can not replace the original allocation vlan10 swap which Taiwan switchboard. Solve the problem.
I think the key issue is that it can discover the other vlan, the LAN Switch comes in 4, 5! Oh nothing!
Interface FastEthernet0/1 FuFeiHuaYanLou description Up Line
Switchport mode trunk
Vlan port trunk permit seemed to be all of Canada.
Do not hit me! ! Ha ha
At this time the Port of Orange does not mean that you are the VTP VLAN 10 VLAN switches can learn, you can add your own needs manual VLAN oh Answer : I have the eighth floor LAN Switch Lane has been used in 40 to Taiwan the trunk switchport mode trunk so that the problem will be 4, 5. Not like this. A 9, 10 : Building on its switchboard level, all the vlan vtp all have to recognize it here only two, it is the key to why not learn while other will be able to learn, and I have appointed a three-tier exchange Lane v10 and v11, v10, and he learned a v11. terror is the future use if needed vlan seemed to be moved to other secondary switches to learn about.
Vlan hand but do not know it can be added to the other switches and LAN Lane vlan whether the same can not use the normal tried.
Thank you, I have time to go try.
Second, the solution is the 10th floor Sw-2950_ffcbgl#vlan database
Warning : It is recommended to configure% from configure VLAN mode.
As VLAN database mode is being deprecated. Please consult a user
Documentation for configuring VTP/VLAN in configure mode.
Sw-2950_ffcbgl (vlan) #vlan 6
VLAN 6 added :
Name : VLAN0006
Sw-2950_ffcbgl (vlan) #exit
APPLY completed.
Exiting. . . .
Sw-2950_ffcbgl#sho vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
5 VLAN0005 active
6 VLAN0006 active
10 VLAN0010 active Fa0/12, Fa0/13
11 VLAN0011 active Fa0/2, Fa0/3, Fa0/4, Fa0/5
Please also analyze why not automatically learn vlan information.
Sh vtp status (Vtp not to learn the switchboard) Sw-2950_ffcbgl#sh vtp status
VTP Version 2 :
Configuration Revision 7 :
Maximum VLANs supported locally : 64
11 : Number of existing VLANs
VTP Operating Mode : Server
VTP Domain Name : ydsec
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
0xF7 0x7D MD5 digest : 0x48 0x73 0xB4 0x1B 0x8E 0x0F
Configuration last modified by 172.16.1.24 at 3-1-93 03:50:56
Local updater ID is 172.16.1.24 on interface Vl1 (lowest numbered VLAN interface
Found)
(Vtp normal switchboard)
Sw-2950G_ffchyl#sh vtp status
VTP Version 2 :
Configuration Revision : 22
Maximum VLANs supported locally : 250
22 : Number of existing VLANs
VTP Operating Mode : Client
VTP Domain Name : Tj_Group
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xF0 0x4E 0x8A 0x79 0x84 0x3A 0xBC 0xB6
Configuration last modified by 172.16.1.1 at 4-4-04 14:07:15
VTP Operating Mode : Server---->Client VTP Domain Name : ydsec------>Tj_Group
You to the same VTP DOMAIN NAME!