New opportunities, and under no f0/1 shut, open port on the following error, and now is how else 00:16:35 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
00:16:45 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
Double rate issue and whether ah? Please check! Should not, f0/1 adapter celebrate inserted lines. On the incorrect report. While transmitting a frame. the local buffer of the controller chip received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally, such a problem is temporar y, depending on transient peak loads within the system. The system should recover. What is look at the issue. 01:07:25 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:07:35 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
Router>enable
Router#show run
Building configuration. . .
Current configuration : 424 bytes
!
Version 1.22
Killing uptime service timestamps
Service timestamps log uptime
No service password-encryption
!
Hostname Router
!
!
Ip subnet-zero
!
!
!
!
!
!
Interface FastEthernet0/0
No ip address
Shutdown
Duplex auto
Speed auto
--More--!
Interface FastEthernet0/1
Ip address 192.168.0.1 255.255.255.0
Duplex auto
Speed auto
!
Ip classless
Ip http server
Ip pim bidir-enable
!
!
!
Line con 0
Line aux 0
Line vty 0 4
!
!
End
Router#
01:07:45 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
Router#show int f0/1
01:07:55 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
FastEthernet0/1 is up, line protocol is down
Hardware is AmdFE, address is 000e.d759.8d61 (bia 000e.d759.8d61)
Internet address is 192.168.0.1/24
MTU 1500 bytes, BW 000-Kbit, DLY 100 usec.
Reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto Speed, 100BaseTX/FX
ARP type : ARPA, ARP Timeout 04:00:00
Last input 00:23:00, 00:00:01 output, the output hang never
Last clearing of "show interface" counters never
Input queue : 0/75/0/0 (size/max/drops/flushes); Total output drops : 0
Queuing strategy : fifo
Output queue : tissues (size/max)
5 minute input rate bits/sec 0 0 packets/sec
5 minute output rate bits/sec 0 0 packets/sec
370 packets input, 35181 bytes
Beijing 254 broadcasts, 0 runts, 0 giants, 0 throttles
524 input errors, 0 CRC, frame 0 0 overrun, 524 ignored
TM 0
0 input packets with dribble condition detected
552 packets output, 43260 bytes, 1108 underruns
0 output errors, 0 collisions, 1 interface resets
Babbles --More-- 0 0 late AVLIS, 4 deferred
293 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Router#
01:07:56 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
Router#
01:08:15 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:08:25 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
Router#show ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IM), Version 12.2 (8) T10, RELEASE SOFTWARE (fc1)
TAC Support : http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled by kellythw Fri 02:45 30-May-03
Image text-base : 0x80008074, data-0x80A2C2B0 :
ROM : System Bootstrap, Version 12.2 (8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Router uptime is 1 hour, 8 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.122-8.T10.bin"
Creating 2611XM (MPC860P) processor (revision 0x200) with 27648K/5120K bytes of memory.
Processor board ID JAE07520LFH (495477915)
M860 processor : part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface (s)
32K bytes of memory non-volatile configuration.
16384K bytes of processor board System flash (Read)
--More-- Configuration register is 0x2102
Router#
01:08:35 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:08:45 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:08:55 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:09:05 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:09:15 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :
01:09:25 : %AMDP2_FE-3-UNDERFLO FastEthernet0/1 transmit error :